Alexor PC9155D-433 Manual do Utilizador descarregar pdf (Página 2)

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Dig-

ital Security Controls could void your authority to use this equipment.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are de-

signed to provide reasonable protection against harmful interfer-ence in a res-

idential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Re-orient the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult a dealer or experienced radio/television technician for help.

The user may find the following booklet prepared by the FCC useful: "How to

Identify and Resolve Radio/Television Interference Problems". This booklet

is available from the U.S. Government Printing Office, Washington D.C.

20402, Stock # 004-000-00345-4.

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC Rules and, if the product

was approved July 23, 2001 or later, the requirements adopted by the ACTA.

On the top side of this equipment is a label that contains, among other infor-

mation, a product identifier. If requested, this number must be provided to the

Telephone Company.

Product Identifier: US:F53AL01B9155

USOC Jack: RJ-31X

Telephone Connection Requirements

A plug and jack used to connect this equipment to the premises wiring and tel-

ephone network must comply with the applicable FCC Part 68 rules and re-

quirements adopted by the ACTA. A compliant telephone cord and modular

plug is provided with this product. It is designed to be connected to a compat-

ible modular jack that is also compliant. See installation instructions for de-

tails.

Ringer Equivalence Number (REN)

The REN is used to determine the number of devices that may be connected

to a telephone line. Excessive RENs on a telephone line may result in the de-

vices not ringing in response to an incoming call. In most but not all areas, the

sum of RENs should not exceed five (5.0). To be certain of the number of de-

vices that may be connected to a line, as determined by the total RENs, contact

the local Telephone Company. For products approved after July 23, 2001, the

REN for this product is part of the product identifier that has the format US:

AAAEQ##TXXXX. The digits represented by ## are the REN without a dec-

imal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separate-

ly shown on the label. REN = 0.1B

Incidence of Harm

If this equipment (PC9155-433) causes harm to the telephone network, the tel-

ephone company will notify you in advance that temporary discontinuance of

service may be required. But if advance notice is not practical, the Telephone

Company will notify the customer as soon as possible. Also, you will be ad-

vised of your right to file a complaint with the FCC if you believe it is neces-

sary.

Changes in Telephone Company Equipment or Facilities

The Telephone Company may make changes in its facilities, equipment, op-

erations or procedures that could affect the operation of the equipment. If this

happens the Telephone Company will provide advance notice in order for you

to make necessary modifications to maintain uninterrupted service.

Equipment Maintenance Facility

If trouble is experienced with this equipment (PC9155/WT5500) for repair or

warranty information, contact the facility indicated below. If the equipment is

causing harm to the telephone network, the Telephone Company may request

that you disconnect the equipment until the problem is solved. This equipment

is of a type that is not intended to be repaired by the end user.

DSC c/o APL Logistics 757 Douglas Hill Rd., Lithia Springs, GA 30122

Additional Information

Connection to party line service is subject to state tariffs. Contact the state

public utility commission, public service commission or corporation commis-

sion for information.

Alarm dialling equipment must be able to seize the telephone line and place a

call in an emergency situation. It must be able to do this even if other equip-

ment (telephone, answering system, computer modem, etc.) already has the

telephone line in use. To do so, alarm dialling equipment must be connected

to a properly installed RJ-31X jack that is electrically in series with and ahead

of all other equipment attached to the same telephone line. Proper installation

is depicted in the figure below. If you have any questions concerning these in-

structions, you should consult your telephone company or a qualified installer

about installing the RJ-31X jack and alarm dialling equipment for you.

INDUSTRY CANADA STATEMENT

NOTICE: This product meets the applicable Industry Canada technical

specifications.

Le présent materiel est conforme aux specifications techniques applicables

d’Industrie Canada.

The Ringer Equivalence Number (REN) for this terminal equipment is 0.1.

L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1.

The Ringer Equivalence Number is an indication of the maximum number of

devices allowed to be connected to a telephone interface. The termination on

an interface may consist of any combination of devices subject only to the re-

quirement that the sum of the RENs of all the devices does not exceed five.

L’indice d’équivalence de la sonnerie

(IES) sert à indiquer le nombre maximal de terminaux qui peuvent être rac-

cordés à une interface téléphonique. La terminaison d’une interface peut con-

sister en une combinaison quelconque de dispositifs, à la seule condition que

la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’ex-

cède pas 5.

The term ’IC:’ before the radio certification number only signifies that Indus-

try Canada technical specifications were met.

Certification Number IC: 160A-PC9155

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du

Canada.

Telephone

Computer

Telephone

Fax Machine

Alarm Dialing

Equipment

RJ-31X

Jack

Unused

RJ-11 Jack

Telephone

Line

Network

Service

Provider's

Facilities

Customer Premises Equipment and Wiring

Unused

RJ-11 Jack

Network

Demarcation

Point

Answering

System

1 2 3 4 5 6 7 ... 23 24

Comentários a estes Manuais

Sem comentários

Alexor PC9155D-433 Manual do Utilizador Página 2

Comentários a estes Manuais